What does label means?

1. STRUCTURE OF LABELING OF BACKBONE AND BACKHAUL OPTICAL CABLES

STRUCTURE OF LABELING OF BACKBONE AND BACKHAUL OPTICAL CABLES
OK	G	M	ng(А)	- HF	-01	-3х4Е3/...*	-(7,0) -Т**
							Allowable tensile force (static), kN
						Number of OF х Number of OF in LT
						Type of OF:
						Е3 - single-mode OF with low-water peak according to ITU-T G.652.D with reduced radius of bending according to ITU-T G.657.A1; or single-mode OF with low-water peak according to ITU-T G.652.D
						Е5 - single-mode OF with non-zero shifted dispersion according to ITU-T G.655
						М1 (ОМ2) - multimode OF 50/125 according to ITU-T G.651.1
						М2 (ОМ1) - multimode OF 62.5/125 according to IEC60793-2-10
						М3 (ОМ3)- multimode OF 50/125 according to ITU-T G.651.1
						М4 (ОМ4) - multimode OF 50/125 according to recommendation ITU-T G.651.1
					Designs:
					00 - single-tube, no central strength member
					01 - multi-tube, central strength member (or outer strength member for OKPM and OKPTS) – one or two (for cables OKPP) with FRP rods
					02 - multi-tube, central strength member or outer strength member (for OKPM and OKPTS} – steel strand
					03 - multi-tube, central strength member or outer strength member (for OKPM and OKPTS} – steel wire
					04 - multi-tube, outer strength member for OKPM and OKPTS – aramid filament
			Cable with PE fire-retardant sheath:***:
			n - in individual installation
			ng(А) - in bundle installation
			ng(А) - LS – in bundle installation, with low liberation of smoke and gas
			ng(А) - HF – in group installation, without liberation of corrosive gaseous products when burning and smoldering
			ng(A)-FR – fire resistant, flame-retardant in bundle installation
			ng(A)-LTx- flame-retardant in bundle installation, with low toxicity of combustion products
		Type of design:
		M - loose tube design
		TS - design with a central tube
		P - flat
		D - dielectric (certified by Federal network company UNIFIED ENERGY SYSTEM, for suspension on power lines)
		d - dielectric (armor made of FRP rods for cables OKGM, OKGTS)
		s - only for self-supporting cable, design with glass filament (OKSMs)
	Type of installation:
	G - optical cable for direct bury
	K - optical cable for installation in channels.
	P - suspension optical cable.
	S - self-supporting optical cable.
	Т - optical cable for nstallation in pipes.
Optical cable

2. STRUCTURE OF MARKING OF COMPOSITE CABLES

STRUCTURE OF MARKING OF COMPOSITE CABLES WITH OPTICAL FIBERS AND COPPER CONDUCTORS
KSPP	OC	G	M	ng(A)	-4Мх0,9/	-01	-3х4Е3/...*	-(7,0)
								Allowable tensile force (static), kN
							Number of LT х number of OF in LT:
							Type of OF:
							Е3 – single-mode OF with low water peak according to ITU-TG.652.D with a reduced radius of bending according to ITU-TG.657.A1; or single-mode OF with low water peak according to ITU-TG.652.D
							Е5 – single-mode OF with non-zero dispersion according to Recommendation ITU-T G.655
							М1 (ОМ2) – multimode OF 50/125 according ITU-T G.651.1
							М2 (ОМ1) - multimode 62.5/125 according IEC 60793-2-10
							М3 (ОМ3)- multimode 50/125 according ITU-T G.651.1
							М4 (ОМ4) - multimode 50/125 according ITU-T G.651.1
						Design:
						01 – multitube, central strength member (or outer member for KSPP OKPM)
						02 – multitube, central strength member (outer member, for KSPP OKPM), steel strand
						03 – multitube, central strength member (outer member for KSPP OKPM), steel wire
						04 – mulitube, outer strength member, for OKPM and OKPTS – aramid filament
					Number of copper conductors x rated diameter of a copper conductor
				Fire-retardant PE sheath:
				n – in individual installation;
				ng(A) – in bundle installation;
				ng(А)-LS – in bundle installation with lower smoke and gas liberation;
				ng(А)-HF – in bundle installation without liberation of corrosive gaseous products when burning or smoldering
			Type of design:
			М – loose tube design
		Type of installation:
		G – optical cable for direct bury
		К – optical cable for installation in channels
		P –suspension optical cable
		Т – optical cable for installation in pipes
	Optical cable
C – cable, S – local network, P – polyethylene sheath, P – protective PE sheath

STRUCTURE OF MARKING OF COMPOSITE SELF-SUPPORTING WIRE WITH OPTICAL FIBERS
SIP	-3	1х70	-20/	О	М	-16E3*
						Number of OF
						Type of OF:
						Е3 – single-mode OF with low water peak according to ITU-TG.652.D with reduced radius of bending ac- cording to ITU-TG.657.A1 («Асе»); or single-mode OF with low peak water according to ITU-TG.652.D
						Е5 – single-mode OF with non-zero shifted dispersion according to ITU-T G.655
						М1 (ОМ2) – multimode OF 50/125 according to ITU-T G.651.1
						М2 (ОМ1) – multimode OF 62.5/125 according to IEC60793-2-10
						М3 (ОМ3)- multimode OF 50/125 according to ITU-T G.651.1
						М4 (ОМ4) – multimode OF 50/125 according to ITU-T G.651.1
					Type of design:
					M – loose tube design
					TS – design with a central tube
				Optical part
			Rated voltage (kV)
		Number of conductors х rated cross-section of conductor (mm2)
	Type of wire design
Self-supporting insulated wire

3. STRUCTURE OF CABLE MARKING FOR LANs

STRUCTURE OF CABLE MARKING FOR LANs
OC	V	ng(А)	-02-	-1х4	G.657.A1	-B0,9-	-(1,0)
							Allowable tensile force (static), kN
						Special features of design (this column is not available in cable marking of OKDP):
						B – OF in tight buffer, the figure after the latter designate the outer diameter of one fiber in in tight buffer.
						М – microtubes are used in the cable, the figure after the letter designates the diameter of one microtube
						3.0/0.9 – diameter of Simplex or dimensions of Duplex, height/diameter of optical fiber in tight buffer.
					Type of optical fiber:
					G.652.D – single-mode OF with low-water peak according to Recommendation ITU-TG.652.D
					G.655 – single-mode OF with non-zero shifted dispersion according to Recommendation ITU-T G.655
					G.657.A1 - single-mode OF with reduced radius of bending according to Recommendation ITU-T G.657.А1
					G.657.А2 - single-mode OF with reduced radius of bending according to Recommendation ITU-T G.657.А2
					ОМ1 – multimode OF 62.5/125 according to IEC60793-2-10
					ОМ2 – multimode OF 50/125 according to ITU-T G.651.1
					ОМ3 – multimode OF 50/125 according to ITU-T G.651.1
					ОМ4 - multimode OF 50/125 according to ITU-T G.651.1
				Number of optical fibers or number of microtubes х number of OF in a micromodule. In designs with one bunch of fibers (without microtubes) the first figure in this column is not available.
			Engineering design (ONLY IN MARKING OF CABLES OKPD):
			00- strength members: 2 FRP rods
			01- strength members: 2 steel wires
			02 –outer strength member: steel wire and strength elements: 2 FRP rods
			03 - outer strength member: steel wire and strength elements: 2 steel wires
			04 - outer strength member: one FRP rod and strength elements: 2 FRP rods
			05 - outer strength member; one FRP rod and strength elements: 2 steel wires
		Sheath made of fire-retardant PE: *:
		ng(А) – in bundle laying
		ng(А)-LS – in bundle laying, with lower smoke and gas liberation
		ng(А)-HF – in bundle laying (halogen-free)

	Type of design:
	V – optical cable for vertical installation (type «Riser»)
	D – subscriber’s optical cable (type «Duplex»)
	DP – optical cable, drop flat and drop flat with an outer strength member
	R – distribution optical cable (type «Distribution»)
	S – subscriber’s optical cable (type «Simplex»)
	Т – optical fiber in tight buffer
Optical cable